Shark Robot Vacuum Troubleshooting – Top 15 Problems & Solution

The shark robot vacuum is one of the most popular robotic vacuum cleaners on the market. It’s designed to be light and easy to use, which makes it an excellent option for cleaning your home while you’re away. But how can you tell if there is something wrong with your shark?

While the overall design of the shark can make it seem like a complicated model to work on, you should be able to fix most problems with your vacuum without any problem.

Most issues you encounter will probably be related to the battery or charging. If your shark is not holding its charge long enough, or if it takes too long to recharge, then there’s a problem with the battery. The good news is that most parts of the vacuum can be replaced easily, including both the batteries and the charger.

If you’re not sure where to start or if your shark robot vacuum has stopped working correctly, then you should check out the Shark Robot Vacuum Troubleshooting guide to find any problems and get them fixed right away.

Top 15 Problems & Solutions Of Shark Robot Vacuum

1. Shark Robot Vacuum Stuck

Sometimes when cleaning your home, your shark vacuum can get stuck. If you notice that your robot vacuum is struggling to move, then there are a few things you can do to help it out.

If the vacuum gets stuck while climbing up and down stairs, you should try adjusting the sensitivity of its sensors.

This will make it easier for the vacuum to detect stairs and other obstacles in front of it. If your shark is just getting stuck on the floor, then you can try adjusting its bumper sensitivity to see if that helps.

2. Shark Robot Vacuum Filter Problems

One of the main components of a shark cleaning system is its filters. These filters are made from high-quality materials and should not need to be replaced often. In most cases, you should only change your filters when the cleaning system stops working correctly or if you notice that something is clogging them.

Solution

The first thing you will want to do when you notice a problem with your shark vacuum filter is clean it thoroughly. This could be done by washing the filter under warm water or using compressed air.

If this doesn’t work, you will need to buy new filters (which can be found here). Make sure that you have the right type of filters for your vacuum’s model.

3. Shark Robot Vacuum Not Picking Up

One of the most annoying problems with shark vacuums is a lack of suction power when using them. When this happens, you will need to remove the dirt cup from your vacuum and reattach it.

Solution

If you notice that your shark vacuum is not picking up when using it, there is probably debris or something else stuck inside its dirt bin. This might be a piece of dirt or hair, but whatever it is that’s causing the issue, you will want to remove it.

4. Shark Robot Vacuum Overheating

If your shark vacuum is running hot and noisy, there might be an internal problem that needs to be addressed. There are two main reasons why your vacuum could overheat: a clogged filter or a malfunctioning motor. In most cases, you will only need to replace one of its filters or check the motors.

Solution

If your vacuum is overheating, you should turn it off immediately and unplug it. This way, you won’t risk damaging the inner components of your vacuum. Make sure that there are no blockages in the dirt bin before doing so. Next, remove the dirt bin and check for any blockages.

After that, plug the vacuum in again and see if it stops overheating. If you notice that something is wrong with your motor, you will need to replace it (which can be found here).

5. Shark Robot Vacuum Battery Issues

One common problem with shark vacuums is when they do not hold a charge. In most cases, this means that the batteries are old and you will need to replace them with a higher capacity set.

Solution

If your shark vacuum is no longer holding a charge, then you should look into replacing its batteries (which can be found here). The first step of doing so is to find the make and model of your vacuum. Check the battery compartment for this information. Next, order a new set of batteries that will be compatible with your shark cleaning system.

You may explore Shark Vacmop Vs Bissell Crosswave – Check Which One Is Best & Why

6. Shark Robot Vacuum Red Light Flashing

Red lights flashing on your shark vacuum indicate that it requires charging. If you see these lights flashing, you should plug your cleaning system into a power outlet and let it sit until the lights turn off.

Solution

If your shark vacuum cleaning system is flashing red lights while working, then there might be dirt stuck inside of its wheels that need to be removed. Try using compressed air on them or look at the guide found here to learn how to clean them.

7. Shark Robot Vacuum Spits Out Dirt

There are several reasons why your Shark cleaning system might spit out dirt when you’re trying to clean on a particular area. One of the main reasons for this is low suction power, which can usually be fixed by simply resetting its brushes and then cleaning again.

Solution

If your shark vacuum is spitting out dirt when you are trying to clean, it might be because there is debris stuck in its brushes or filter. To fix an issue with the brush roll, reset it and try cleaning again. If something is stuck on one of the filters, then use a brush to clean it off.

8. Shark Robot Vacuum Won’t Turn On or Charge

There are several reasons why your shark vacuum cleaner could stop working, including a dead battery or fuse in the plug. Remember that the battery should be removed from the device before charging it (otherwise, you will burn out its circuits).

Solution

If your shark vacuum is not turning on, then there might be an issue with its battery. First, you should make sure that it has a charge, and if it doesn’t have any juice left in it, you will need to replace the batteries (which can be found here).

Another reason for your shark cleaning system’s power failure could be a blown a fuse in the plug. To fix this, all you need is a replacement fuse that will work with your device (you can find it here).

9. Shark Robot Vacuum Keeps Falling Down or Off Ledges

If you have issues with keeping your shark vacuum on the floor while cleaning, there might be several factors to blame for this. To start with, look at the surface. Is it slippery or smooth? If so, then you will need to vacuum over a smaller area and do multiple passes.

Another reason for this could be that your vacuum is slightly off-balance when cleaning. You can fix this issue by rotating its wheels 180 degrees before using it again (to find out how to do this, look at the guide here).

Solution

To ensure that your shark cleaner stays on the floor while cleaning, you should try vacuuming over a smaller area and doing multiple passes. If it is still falling over or parts of your surface that you might want to avoid, consider getting one of the robot vacuum bumpers that is sold here.

10. Shark Robot Vacuum Keeps Going In Circles

If your shark vacuum is constantly moving around in circles instead of working on a particular area, then there could be several reasons for this. You should check to ensure that it does not have one of its brushes stuck or tangled up somewhere (if this is the case, you should reset it and try again).

Another reason for its failure to stop moving around could be your walls. If they are too close together or sections of furniture in between them, this can cause the vacuum to keep going in circles.

Solution

If your shark robot vacuum keeps going in circles while you are trying to use it, then there is a chance that one of its brushes is stuck. To fix this problem, try resetting the rollers and see if they move. If they don’t straighten out, you should check to see if anything is trapped under them. You can find directions on how to clean these here.

If the vacuum keeps moving around in circles because of your walls or furniture, then you might want to try getting one of these bumpers so the device will have something to push against and not keep going in circles.

11. Shark Robot Vacuum Battery Drained After Only An Hour

If your robotic shark vacuum has a short battery life (less than an hour), several factors are to blame for this. First of all, remember that when you charge your battery, it should be removed from the device and not left in it (otherwise, you might burn out its circuits).

Secondly, it is possible that your cleaning system’s battery got drained during shipping or storage. Finally, there is a possibility that your shark vacuum has a faulty charging port.

Solution

To ensure that you’re not draining your battery, it is always best to charge it outside of the machine and taking out its batteries (to learn how to do this, click here ). Secondly, if you believe that your device’s battery got drained before using it or during storage, then you can replace it with a brand new one here.

Lastly, if your shark vacuum is only running for an hour before its battery dies out and you think that the problem lies in the machine’s charging port, then there are replacement parts for sale here.

12. Shark Robot Vacuum Not Charging

The first problem you might encounter with your shark is that it is not holding a charge. Perhaps the vacuum will run for a few minutes but then suddenly dies. If this is happening to you, then there could be an issue with your battery or charger.

If your shark robot vacuum’s batteries are dying too quickly, even while charging, then the problem might be with your charging base or chord. A switch on the charger changes how fast it charges, so try using this until you find the right speed for your robot’s batteries.

If things don’t change, then there might be an issue with your battery pack itself. Usually, you will need to replace this battery, but you should try cleaning it first. Many users forget to clean the battery pack, and dust and debris build up over time inside the battery. This can cause issues with charging or power, so be sure to give yours a good wash before trying anything else.

Solution

One of the best ways to clean your robot’s battery is with a mild soap solution. Make sure you get all the soap off before putting the battery back in your shark.

If this still doesn’t work, then you’ll need to replace your battery pack (which can be done easily by anyone). Many people wonder if they should buy a new battery or just buy a new shark. The answer depends on how long you’ve had your vacuum and its overall condition, but it’s usually best to purchase a new unit instead of batteries for your vacuum.

12. Shark Robot Vacuum Not Docking

If your vacuum is getting stuck on walls or refusing to dock at all. Then there might be an issue with the Smart Nav system. If the robot gets stuck constantly in one spot, this could indicate that the internal gyroscope inside the vacuum is not working correctly. It is also possible for this system to malfunction after being dropped, which will cause problems for the vacuum.

If your shark is having difficulty following its charging base, then the internal gyroscope might need to be calibrated. One way to do this is by using a rubber band and placing it on the front of your robot vacuum.

Solution

If your robot vacuum is having a hard time following the charging base, you should place an object in front of it. This could be a bag of rice, a book or anything else that will challenge the shark’s navigation system to function correctly.

13. Shark Robotic Vacuum Won’t Pick Up Pet Hair or Other Debris

If you have pets that shed a lot of other fur-like substances floating around in your home, it will be difficult for your shark vacuum to pick them up. This can cause the device to clog and potentially burn out its circuits. There are several ways you can clean out this sort of debris.

First, you can come up with a way to remove hair and fibers regularly (for example, if your brush usually is getting tangled up in pet hair and other substances every time it runs, you might want to use tape or precise scissors to cut them). Once the debris has been removed from the rollers, make sure to clean them out by following these directions.

Solution

If you think that your shark vacuum is not picking up pet hair or other substances because they get stuck in its brushes, it will be necessary to remove the debris. When cleaning out the rollers, make sure they are completely dry before replacing them with your device.

14. Shark Robotic Vacuum Turns Off While In Use

If your shark is turning off and on during cleanup, then there are a few things you can try before giving up on your expensive cleaning device. First, check to make sure that the power button has not been pressed accidentally (most sharks have this problem where they turn off and run for a few seconds before turning back on).

If this is not the case, then it might be necessary to clean out your device’s brushes. Brush-less vacuums have a different cleaning system that does not need as much maintenance (but they also have their drawbacks ).

Solution

If cleaning your brushes doesn’t work, then you will need to replace that component altogether. It is effortless to do so, and the process usually only takes about ten minutes or less.

Conclusion

If you have followed all of the steps above and your shark vacuum still won’t pick up, it might need a new motor or other significant components. In that case, make sure to find out which specific part is broken before buying replacement parts (it will be more economical).

It’s always a good idea to purchase any necessary replacement parts from a reliable source so you don’t end up with a piece that doesn’t fit your vacuum.

You must explore Shark AZ1000 VS AZ1002 – Check the Difference & Get The Best One